|
軟件簡介：
目 次
1 總則 1 2 術語 2 3 基本規定 3 3.1 施工管理 3 3.2 施工技術 3 3.3 施工質量與安全 3 4 模板工程 5 4.1 一般規定 5 4.2 材料 5 4.3 設計 5 4.4 制作與安裝 8 4.5 拆除與維護 11 4.6 質量檢查 11 5 鋼筋工程 14 5.1 一般規定 14 5.2 材料 14 5.3 鋼筋加工 14 5.4 鋼筋連接與安裝 16 5.5 質量檢查 19 6 預應力工程 20 6.1 一般規定 20 6.2 材料 20 6.3 制作與安裝 20 6.4 張拉與放張 23 6.5 灌漿與封錨 26 6.6 質量檢查 28 7 混凝土制備與運輸 30 7.1 一般規定 30 7.2 原材料 30 7.3 混凝土配合比 32 7.4 混凝土攪拌 34 7.5 混凝土運輸 35 7.6 質量檢查 36 8 現澆結構工程 39 8.1 一般規定 39 8.2 混凝土輸送 39 8.3 混凝土澆筑 41 8.4 混凝土振搗 45 8.5 混凝土養護 47 8.6 混凝土施工縫與后澆帶 48 8.7 大體積混凝土裂縫控制 50 8.8 質量檢查 51 8.9 混凝土缺陷修整 53 9 裝配式結構工程 56 9.1 一般規定 56 9.2 施工驗算 56 9.3 構件制作 58 9.4 運輸與存放 60 9.5 安裝與連接 61 9.6 質量檢查 62 10 冬期、高溫與雨期施工 64 10.1 一般規定 64 10.2 冬期施工 64 10.3 高溫施工 67 10.4 雨期施工 68 11 環境保護 70 11.1 一般規定 70 11.2 環境因素控制 70 附錄A 作用在模板及其支架上的荷載標準值 72 附錄B 常用鋼筋的規格和力學性能 74 附錄C 常用鋼筋的公稱直徑、公稱截面面積、計算 截面面積及理論重量 76 附錄D 縱向受力鋼筋的最小搭接長度 78 附錄E 張拉階段摩擦預應力損失測試方法 80 附錄F 預應力筋張拉伸長值計算和量測方法 83 附錄G 混凝土原材料技術指標 84 附錄H 大體積混凝土水化熱溫度計算 89 附錄J 混凝土拌合物溫度估算 91 附錄K 混凝土水分蒸發速率估算 92 本規范用詞說明 93 引用標準名錄 94 附：條文說明 95 Contents 1 General Provisions 1 2 Definitions 2 3 Basic Requirements 3 3.1 Construction Management 3 3.2 Construction Technology 3 3.3 Construction Quality and Safety 3 4 Formwork 5 4.1 General Requirements 5 4.2 Materials 5 4.3 Design 5 4.4 Fabrication and Installation 8 4.5 Removal and Maintenance 11 4.6 Quality Control 11 5 Reinforcement 14 5.1 General Requirements 14 5.2 Materials 14 5.3 Reinforcement Fabrication 14 5.4 Reinforcement Connection and Fixing 16 5.5 Quality Control 19 6 Prestressed Concrete 20 6.1 General Requirements 20 6.2 Materials 20 6.3 Fabrication and Installation 20 6.4 Post-tensioning and Pre-tensioning 23 6.5 Grouting and Anchorage Protection 26 6.6 Quality Control 28 7 Concrete Production and Transportation 30 7.1 General Requirements 30 7.2 Materials 30 7.3 Mix Proportioning 32 7.4 Mixing 34 7.5 Conveying 35 7.6 Quality Control 36 8 Cast-in-Situ Concrete 39 8.1 General Requirements 39 8.2 Conveying 39 8.3 Placing 41 8.4 Compacting 45 8.5 Curing 47 8.6 Construction Joint and Post-cast Strip 48 8.7 Crack Control of Mass Concrete 50 8.8 Quality Control 51 8.9 Repair of Concrete Defects 53 9 Precast Concrete 56 9.1 General Requirements 56 9.2 Checking 56 9.3 Production 58 9.4 Storage and Transportation 60 9.5 Erection 61 9.6 Quality Control 62 10 Construction in Cold, Hot and Rainy Weather 64 10.1 General Requirements 64 10.2 Cold Weather Requirements 64 10.3 Hot Weather Requirements 67 10.4 Rainy Weather Requirements 68 11 Environmental Protection 70 11.1 General Requirements 70 11.2 Environmental Considerations 70 Appendix A Characteristic Values of Loads Acting on Formwork 72 Appendix B Specifications and Mechanical Properties of Common Reinforcements 74 Appendix C Nominal Sectional Area, Calculation Sectional Area and Theoretical Weight of Reinforcements 76 Appendix D Minimum Splicing Length of Longitudinal Reinforcements 78 Appendix E Testing Method for Prestressing Loss due to Friction 80 Appendix F Calculation and Measurement Method for Elongation of Prestressed Tendons 83 Appendix G Specifications of Concrete Materials 84 Appendix H Calculation for Hydration Heat Temperature of Concrete 89 Appendix J Temperature Estimation of Fresh Concrete Mixtures 91 Appendix K Estimation of Concrete Evaporation Rate 92 Explanation of Wording in this Code 93 Cited Standards 94 Addition：Explanation of Provisions 95 |
|||||||||||||||||||||||||
